APOGEE INDUSTRIES INC.
827 Lincoln Ave
Unit 6
West Chester, PA 19380
Toll Free : 1.800.745.3530
Fax: 610.719.8013
[email protected]
Print Back
Like the 360a Series Label Applicator, the High Speed Labeler is configurable in three options: merge, blow-on or tamp-blow. What separates the 360a High Speed applicator apart is its high-end dual microprocessor control. The application program is run by a single 32-bit processor while a digital signal processor overlooks the motion loop to increase response times and improve application accuracy. Where other applicators may offer various options, the 360a High Speed has them all as standard features. For the business in need of a heavy-duty, versatile and impeccably accurate applicator, the 360a High Speed Labeler allows for no substitutions.
Unit of Measure

Specifications

Brands

 N/A CTM

Air Consumption at 60 to 90 Pound Per Square Inch (psi) Pressure

 N/A Up to 4 ft³/min

Label Placement (±)

 N/A 1/32 in

Labeling Speed

 N/A Programmable to 1500 inches per minute, to 2100 inches per minute. With oversize unwind and rewind. Programmed with speed profiling ability.

Product Sensing

 N/A Retroreflective scanner provided as standard, other types available

Electrical

Alternating Current Voltage (VAC) Rating

 N/A 108 to 132 V

Frequency

 N/A 50 Hz60 Hz

Phase

 N/A Single

Current

 N/A 10 A

Label Sizes

Minimum Air Blow Label Width

 N/A 3/4 in

Minimum Air Blow Label Length

 N/A 3/4 in

Maximum Air Blow Label Width

 N/A 5 in

Maximum Air Blow Label Length

 N/A 5-1/2 in

Minimum Merge Label Width

 N/A 3/4 in

Minimum Merge Label Length

 N/A 3/4 in

Maximum Merge Label Width

 N/A 5 in

Maximum Merge Label Length

 N/A 20 in

Minimum Tamp Label Width

 N/A 3/4 in

Minimum Tamp Label Length

 N/A 3/4 in

Maximum Tamp Label Width

 N/A 5 in

Maximum Tamp Label Length

 N/A 10 in

Label Roll Size

Maximum Label Roll Outside Diameter

 N/A 20 in

Maximum Label Roll Core Inside Diameter

 N/A 3 in

Optional Label Roll Outside Diameter

 N/A 16 in

Optional Label Roll Core Inside Diameter

 N/A 3 in6 in

Dimensions

Air Blow Width

 N/A 39 in

Air Blow Height

 N/A 38-1/2 in

Air Blow Depth

 N/A 27-1/2 in

Merge Width

 N/A 43 in

Merge Height

 N/A 40 in

Merge Depth

 N/A 27-1/2 in

Tamp Width

 N/A 42 in

Tamp Height

 N/A 37 in

Tamp Depth

 N/A 27-1/2 in

Features

Features

 N/A The CTM 360a-HS Series Label Applicator is a rugged, versatile applicator loaded with standard features that are optional on most other applicators. The 360a-HS Series Applicator can be configured as a blow on, merge or tamp applicator. Each module can also be easily switched from right to left hand dispensing mode. Each applicator is equipped with a 20" non-powered unwind/powered rewind.

Stepper Motor

Stepper Motor

 N/A The 360a-HS stepper drive will dispense labels at speeds of 2100 inches/minute.

Controls

Controls

 N/A The 360a-HS is equipped with state-of-the-art electronics featuring Dual Microprocessor control. One 32-bit processor supervises the application program while the digital signal processor (DSP) supervises the motion loop resulting in faster response times and improved application accuracy. The 360a-HS controller is also equipped with onboard I/O prewired to external connectors to accommodate the following:
  • Low Label Conditions
  • Web Break and End of Web Conditions
  • Tamp Extend and Tamp Home Switching
  • Rate and Velocity Compensation
  • Profiling
  • Zero Downtime Configuration of Applicators
Each machine is shipped preprogramed with prewired connectors to control all of the above accessories. Some additional hardware may be required.
The electronic control assembly has been packaged as a module. Each control module can be easily removed for repair or replacement, eliminating costly downtime and servicing costs.